歡迎訪問濟南科爾超聲波設備有限公司網站！

專注生產工業用超聲波清洗機

讓工業清洗無難事

業務咨詢電話：

18663767799

你所在位置：首頁-新聞動態-常見問題

常見問題

高壓去毛刺清洗機運行前后的各個問題排查

作者：admin來源：http://applytechlab.com/時間：2022-12-02

高壓去毛刺清洗機因為是使用高壓水柱清理污垢，所以高壓去毛刺清洗機也是世界公認科學、經濟、環保的清潔方式之一。下面來講講高壓去毛刺清洗機運行前后的各個問題排查。

High pressure deburring cleaning machine is one of the world recognized scientific, economic and environmental cleaning methods because it uses high pressure water column to clean dirt. Let's talk about the troubleshooting before and after the operation of the high-pressure deburring washer.

一、高壓去毛刺清洗機在運行的過程中如果出現異常的尖叫聲，大部分原因是由于電機軸承缺油導致的。這時我們只要在電機的注油孔注入普通黃油就可以解決，這種情況發生的不多。我們在高壓去毛刺清洗機定期檢修維護時給予補充就可以了。

1、 If abnormal squeal occurs during the operation of the high-pressure deburring washer, most of the reasons are due to the lack of oil in the motor bearing. At this time, we only need to inject ordinary butter into the oil injection hole of the motor to solve this problem, which rarely happens. We can supplement the high-pressure deburring cleaning machine for regular maintenance.

二、高壓去毛刺清洗機在啟動后，出現壓力不穩定或時有時無，這里多數原因是高壓水泵或進水管路內吸入了空氣所導致的，這時需要檢查水源的壓力是否足夠，進水過濾器是否堵塞，如果發現進水濾網堵塞,將濾網取下用水清洗就可以了。

2、 After the high-pressure deburring cleaning machine is started, the pressure is unstable or sometimes absent. Most of the reasons are caused by the intake of air in the high-pressure water pump or water inlet pipe. At this time, it is necessary to check whether the pressure of the water source is sufficient and whether the water inlet filter is blocked. If the water inlet filter screen is blocked, remove the filter screen and clean it with water.

三、高壓去毛刺清洗機在運行的過程中有一定的工作壓力但是調不到設備的額定壓力或者說壓力只停留在一定范圍內而不能上升，在這種情況下，首先要判斷高壓噴嘴的孔徑是否匹配。如更換高壓噴嘴后壓力仍然上不去，這時需要查看調壓閥是否調到位了，如果在排除這兩種情況下故障依舊，這說明泵內密封組件（水封）損壞或者是活塞損壞，這種情況需要聯系廠商協助維修。

3、 The high-pressure deburring washer has a certain working pressure during operation, but cannot adjust to the rated pressure of the equipment, or the pressure only stays within a certain range and cannot rise. In this case, it is necessary to judge whether the aperture of the high-pressure nozzle matches. If the pressure still cannot rise after the high-pressure nozzle is replaced, check whether the pressure regulating valve is adjusted to its position. If the fault persists after the two conditions are eliminated, it means that the sealing component (water seal) in the pump is damaged or the piston is damaged. In this case, contact the manufacturer for assistance in maintenance.
高壓去毛刺清洗機

四、高壓去毛刺清洗機在正常運轉一定時間后壓力降低，這種情況首先要檢查高壓噴嘴是否嚴重磨損，普通壓力設備的高壓噴嘴基本上不會出現磨損現象，因為我們所配的高壓噴嘴都進行過熱處理。而高壓設備的高壓噴嘴就難以保證了。其次需要分別檢查調壓閥和水泵內部的密封組件。

4、 The pressure of the high-pressure deburring washer decreases after a certain period of normal operation. In this case, first check whether the high-pressure nozzle is seriously worn. The high-pressure nozzle of ordinary pressure equipment will not be worn basically, because the high-pressure nozzle we have equipped is subject to overheating treatment. The high-pressure nozzle of high-pressure equipment is difficult to guarantee. Secondly, check the pressure regulating valve and the sealing components inside the water pump respectively.

五、啟動設備后，高壓水泵沒有水射出，這時需要廠商維修人員檢查。大部分原因是進水流量閥不能打開造成的，如果排除這種情況下問題依舊，那就是高低壓水路串聯了，也就是說低壓管路的水進不了高壓管路，從而高壓水泵無法工作。出現這種現象需要聯系廠商協助維修解決。

5、 After the equipment is started, no water is ejected from the high-pressure water pump, which requires the manufacturer's maintenance personnel to check. Most of the reasons are that the inlet flow valve cannot be opened. If the problem still exists, the high and low pressure water circuits are connected in series, that is, the water in the low pressure pipeline cannot enter the high pressure pipeline, so the high pressure water pump cannot work. In case of this phenomenon, the manufacturer should be contacted to assist in maintenance and solution.

關于高壓去毛刺清洗機運行前后的各個問題排查的相關內容就講解到這里了，您對此有什么想咨詢的內容就來我們網站applytechlab.com看看吧！

This is all about the troubleshooting of various problems before and after the operation of the high-pressure deburring washer. If you have any questions about this, please visit our website at applytechlab.com!

上一篇：簡答通過式噴淋清洗機的工藝流程
下一篇：碳氫清洗機清洗時的九個要點注意