新手使用工業超聲波清洗機需要注意什么？

作者：admin來源：http://applytechlab.com/時間：2023-06-05

1、仔細使用清洗劑

1. Carefully use cleaning agents

使用超聲波清洗機時，須按說明書要求的順序操作。特別是不允許先啟動機器再倒入清洗劑。這是非法操作，會造成嚴重后果，甚至損壞機器。因此，須先放入液體，然后再打開開關。同時超聲波清洗機廠家提醒，清洗劑的成分也要考慮。如果含有易燃液體，須在短時間內完成操作，整個過程須有監督，不允許離開現場。

When using an ultrasonic cleaning machine, it is necessary to operate in the order required by the manual. Especially, it is not allowed to start the machine before pouring cleaning agent. This is an illegal operation that can cause serious consequences and even damage the machine. Therefore, it is necessary to first put in the liquid before turning on the switch. At the same time, the ultrasonic cleaning machine manufacturer reminds that the composition of the cleaning agent should also be considered. If it contains flammable liquids, the operation must be completed in a short period of time, and the entire process must be supervised. It is not allowed to leave the site.

2、使用腐蝕性或揮發性清洗液時要注意特殊處理

2. Pay attention to special handling when using corrosive or volatile cleaning fluids

一般不建議使用危險的清洗液，但如果情況特殊，強調超聲波清洗機廠家須使用含有腐蝕性或揮發性的液體，那么應采用間接法進行適當處理。根據超聲波清洗機廠家介紹，具體操作方法是先在清洗槽中加水，再在另一個容器中裝滿清洗液，將要清洗的物品放入清洗槽的水中，然后將其浸泡在清洗槽的水中。這樣清洗會有同樣的效果，確保安全。
全自動超聲波清洗機

It is generally not recommended to use hazardous cleaning fluids, but if the situation is special and it is emphasized that ultrasonic cleaning machine manufacturers must use liquids containing corrosiveness or volatility, indirect methods should be used for appropriate treatment. According to the manufacturer's introduction of ultrasonic cleaning machines, the specific operation method is to first add water to the cleaning tank, then fill another container with cleaning solution, put the items to be cleaned into the water of the cleaning tank, and then soak them in the water of the cleaning tank. This cleaning will have the same effect and ensure safety.

3、注意控制清潔的相關因素

3. Pay attention to controlling factors related to cleanliness

超聲波清洗機廠家建議不要把需要清洗的東西放在底部，而是要用專門的清洗支架把它們放在中間的頭頂上，這樣在吃的時候可以受力均勻，獲得良好的清洗效果。同時，超聲波清洗機廠家還應注意，清洗液的能量也要控制好，不能過少，否則儀器可能會損壞或出現故障。

The manufacturer of ultrasonic cleaning machines recommends not placing the items that need to be cleaned at the bottom, but instead using a specialized cleaning bracket to place them on the top of the middle head. This way, the force can be evenly applied while eating, achieving good cleaning results. At the same time, ultrasonic cleaning machine manufacturers should also pay attention to controlling the energy of the cleaning solution well and not too little, otherwise the instrument may be damaged or malfunction.

感謝您的閱讀，此文的文章來源：全自動超聲波清洗機更多的內容和問題請點擊: http://applytechlab.com 我們會繼續努力的為您提供服務，感謝您的支持！

Thank you for reading. The source of this article is: Fully automatic ultrasonic cleaning machine. For more information and questions, please click on: http://applytechlab.com We will continue to work hard to provide you with services. Thank you for your support!

上一篇：使用超聲波清洗機設備您需要注意一下幾點？
下一篇：超聲波清洗機的頻率與功率選擇要看哪些？